Evaluation of Face Shields, Goggles, and Safety Glasses as a Virus Transmission Control Measure to Protect the Wearer Against Cough Droplets.

Face shields (also referred to as visors), goggles and safety glasses have been worn during the COVID-19 pandemic as one measure to control transmission of the virus. However, their effectiveness in controlling facial exposure to cough droplets is not well established and standard tests for evaluating eye protection for this application are limited. A method was developed to evaluate face shields, goggles, and safety glasses as a control measure to protect the wearer against cough droplets. The method uses a semi-quantitative assessment of facial droplet deposition. A cough simulator was developed to generate droplets comparable to those from a human cough. The droplets consisted of a UV fluorescent marker (fluorescein) in water. Fourteen face shields, four pairs of goggles and one pair of safety glasses were evaluated by mounting them on two different sizes of breathing manikin head and challenging them with the simulated cough. The manikin head was positioned in seven orientations relative to the cough simulator to represent various potential occupational exposure scenarios, for example, a nurse standing over a patient. Droplet deposition in the eyes, nose and mouth regions were visualised following three 'coughs'. Face shields, goggles, and safety glasses reduced, but did not eliminate exposure to the wearer from droplets such as those produced by a human cough. The level of protection differed based on the design of the personal protective equipment and the relative orientation of the wearer to the cough. For example, face shields, and goggles offered the greatest protection when a cough challenge was face on or from above and the least protection when a cough challenge was from below. Face shields were also evaluated as source control to protect others from the wearer. Results suggested that if a coughing person wears a face shield, it can provide some protection from cough droplets to those standing directly in front of the wearer.

Simulating the Environmental Spread of SARS-CoV-2 via Cough and the Effect of Personal Mitigations.

BACKGROUND: A cough is known to transmit an aerosol cloud up to 2 m. During the COVID-19 pandemic of 2020 the United Kingdom's National Health Service (NHS), other UK government agencies and the World Health Organization (WHO) advised people to cough into their elbows. It was thought that this would reduce viral spread and protect the public. However, there is limited peer reviewed evidence to support this. OBJECTIVES: To determine if cough related interventions reduce environmental contamination, protecting members of the public from infection. METHODS: Scientists and engineers at the Health and Safety Executive (HSE) laboratory used a human cough simulator that provided a standardised cough challenge using a solution of simulated saliva and a SARS-CoV-2 surrogate virus; Phi6. Pseudomonas syringae settle plates were used to detect viable Phi6 virus following a simulated cough into a 4 × 4 m test chamber. The unimpeded pattern of contamination was compared to that when a hand or elbow was placed over the mouth during the cough. High speed back-lit video was also taken to visualise the aerosol dispersion. RESULTS AND DISCUSSION: Viable virus spread up to 2 m from the origin of the cough outwards in a cloud. Recommended interventions, such as putting a hand or elbow in front of the mouth changed the pattern of cough aerosol dispersion. A hand deflected the cough to the side, protecting those in front from exposure, however it did not prevent environmental contamination. It also allowed for viral transfer from the hand to surfaces such as door handles. A balled fist in front of the mouth did not deflect the cough. Putting an elbow in front of the mouth deflected the aerosol cloud to above and below the elbow, but would not have protected any individuals standing in front. However, if the person coughed into a sleeved elbow more of the aerosol seemed to be absorbed. Coughing into a bare elbow still allowed for transfer to the environment if people touched the inside of their elbow soon after coughing. CONCLUSIONS: Interventions can change the environmental contamination pattern resulting from a human cough but may not reduce it greatly.

A mixed methods study on effectiveness and appropriateness of face shield use as COVID-19 PPE in middle income countries.

BACKGROUND: Face shields were widely used in 2020-2021 as facial personal protective equipment (PPE). Laboratory evidence about how protective face shields might be and whether real world user priorities and usage habits conflicted with best practice for maximum possible protection was lacking - especially in limited resource settings. METHODS: Relative protective potential of 13 face shield designs were tested in a controlled laboratory setting. Community and health care workers were surveyed in middle income country cities (Brazil and Nigeria) about their preferences and perspectives on face shields as facial PPE. Priorities about facial PPE held by survey participants were compared with the implications of the laboratory-generated test results. RESULTS: No face shield tested totally eliminated exposure. Head orientation and design features influenced the level of protection. Over 600 individuals were interviewed in Brazil and Nigeria (including 240 health care workers) in March-April 2021. Respondents commented on what influenced their preferred forms of facial PPE, how they tended to clean face shields, and their priorities in choosing a face cover product. Surveyed health care workers commonly bought personal protection equipment for use at work. CONCLUSIONS: All face shields provided some protection but none gave high levels of protection against external droplet contamination. Respondents wanted facial PPE that considered good communication, secure fixture, good visibility, comfort, fashion, and has validated protectiveness.

Validation of the Decontamination of a Specialist Transport System for Patients with High Consequence Infectious Diseases.

When transferring highly infective patients to specialist hospitals, safe systems of work minimise the risk to healthcare staff. The EpiShuttle is a patient transport system that was developed to fit into an air ambulance. A validated decontamination procedure is required before the system can be adopted in the UK. Hydrogen peroxide (H2O2) vapour fumigation may offer better penetration of the inaccessible parts than the liquid disinfectant wiping that is currently suggested. To validate this, an EpiShuttle was fumigated in a sealed test chamber. Commercial bacterial spore indicators (BIs), alongside organic liquid suspensions and dried surface samples of MS2 bacteriophage (a safe virus surrogate), were placed in and around the EpiShuttle, for the purpose of evaluation. The complete kill of all of the BIs in the five test runs demonstrated the efficacy of the fumigation cycle. The log reduction of the MS2 that was dried on the coupons ranged from 2.66 to 4.50, but the log reduction of the MS2 that was in the organic liquids only ranged from 0.07 to 1.90, confirming the results of previous work. Fumigation with H2O2 alone may offer insufficient inactivation of viruses in liquid droplets, therefore a combination of fumigation and disinfectant surface wiping was proposed. Initial fumigation reducing contamination with minimal intervention allows disinfectant wipe cleaning to be completed more safely, with a second fumigation step inactivating the residual pathogens.

Review of biological risks associated with the collection of municipal wastes.

In many countries, the management of household waste has recently changed with an increased focus upon waste sorting resulting in lower collection frequency for some waste fractions. A consequence of this is the potential for increased growth of microorganisms in the waste before collection, which can lead to an increased exposure via inhalation for waste collection workers. Through a review of the literature, we aimed to evaluate risks caused by waste collecting workers' exposure to bioaerosols and to illuminate potential measures to reduce the exposure. Across countries and waste types, median exposure to fungi, bacteria, and endotoxin were typically around 104 colony forming units (cfu)/m3, 104 cfu/m3, and 10 EU/m3, respectively. However, some studies found 10-20+ times higher or lower median exposure levels. It was not clear how different types of waste influence the occupational exposure levels. Factors such as high loading, ventilation in and cleaning of drivers' cabs, increased collection frequency, waste in sealed sacks, and use of hand sanitizer reduce exposure. Incidences of gastrointestinal problems, irritation of the eye and skin and symptoms of organic dust toxic syndrome have been reported in workers engaged in waste collection. Several studies reported a correlation between bioaerosol exposure level and reduced lung function as either a short or a long term effect; exposure to fungi and endotoxin is often associated with an inflammatory response in exposed workers. However, a better understanding of the effect of specific microbial species on health outcomes is needed to proceed to more reliable risk assessments. Due to the increasing recycling effort and to the effects of global warming, exposure to biological agents in this working sector is expected to increase. Therefore, it is important to look ahead and plan future measures as well as improve methods to prevent long and short-term health effects.

Occupational exposure to fungi on recyclable paper pots and growing media and associated health effects - A review of the literature.

Different types of pots and growing and casing media, including biodegradable materials, are used for plant and mushroom production. The fungus Peziza ostracoderma has gained attention for its visible growth on growing media for plants and casing media for mushrooms. Through a review of the literature we aim to evaluate whether exposure to fungi from recyclable pots and different growing and casing media occurs and causes occupational health effects. Based on the published papers, specific fungal species were not related to a specific medium. Thus P. ostracoderma has been found on paper pots, peat, sterilized soil, vermiculite, and rockwool with plants, and on peat, pumice, and paper casing for mushrooms. It has been found in high concentrations in the air in mushroom farms. Also Acremonium spp., Aspergillus niger, A. fumigatus, Athelia turficola, Aureobasidium pullulans, Chaetomium globosum, Chrysonilia sitophila, Cladosporium spp., Cryptostroma corticale, Lecanicillium aphanocladii, Sporothrix schenckii, Stachybotrys chartarum, and Trichoderma spp. have been found on different types of growing or casing media. Most of the fungi have also been found in the air in greenhouses, but the knowledge about airborne fungal species in mushroom farms is very limited. Eight publications describe cases of health effects associated directly with exposure to fungi from pots or growing or casing media. These include cases of hypersensitivity pneumonitis caused by exposure to: A. fumigatus, A. niger, Au. pullulans, Cr. corticale, P. ostracoderma, and a mixture of fungi growing on different media. Different approaches have been used to avoid growth of saprophytes including: chemical fungicides, the formulation of biodegradable pots and growing media and types of peat. To increase the sustainability of growing media different types of media are tested for their use and with the present study we highlight the importance of also considering the occupational health of the growers who may be exposed to fungi from the media and pots.

Rapid Testing and Interventions to Control Legionella Proliferation following a Legionnaires' Disease Outbreak Associated with Cooling Towers.

Most literature to date on the use of rapid Legionella tests have compared different sampling and analytical techniques, with few studies on real-world experiences using such methods. Rapid tests offer a significantly shorter feedback loop on the effectiveness of the controls. This study involved a complex of five factories, three of which had a history of Legionella contamination in their cooling water distribution system. Multiple sampling locations were utilised to take monthly water samples over 39 months to analyse for Legionella by both culture and quantitative polymerase chain reaction (qPCR). Routine monitoring gave no positive Legionella results by culture (n = 330); however, samples were frequently (68%) positive by qPCR for Legionella spp. (n = 1564). Legionella spp. qPCR assay was thus found to be a good indicator of cooling tower system health and suitable as a routine monitoring tool. An in-house qPCR limit of 5000 genomic units (GU)/L Legionella spp. was established to trigger investigation and remedial action. This approach facilitated swift remedial action to prevent Legionella proliferation to levels that may represent a public health risk. Cooling tower operators may have to set their own action levels for their own systems; however, in this study, 5000 GU/L was deemed appropriate and pragmatic.

Legionella risk in evaporative cooling systems and underlying causes of associated breaches in health and safety compliance.

Legionella bacteria can colonise and proliferate in water systems in the built environment and can be spread by aerosol generation. If inhaled by a susceptible individual, this can lead to respiratory infections such as Legionnaires' Disease (LD), or the generally milder Pontiac fever. Evaporative cooling systems (ECS), including cooling towers, used in industrial processes to dissipate excessive heat are prone to contamination by Legionella. From these systems it is possible for contaminated aerosols to be dispersed over a wide area, potentially exposing workers on site, neighbouring workplaces or nearby members of the public. Analysis of reported data on outbreaks of LD in Great Britain, collated for a ten year period, identified 44 separate legionellosis outbreaks of which seven were attributed to ECS and were responsible for 229 infections and 10 fatalities. This prompted an examination of health and safety inspection records which revealed, over a five year period, 321 enforcement actions taken against failings in Legionella control, of which 31% were attributed to cooling towers. Based on this evidence, an intervention programme was undertaken by health and safety inspectors in which 1,906 sites with ECS were inspected. During these inspections, sites were rated against four topics that are used to demonstrate compliance with statutory requirements for Legionella control: Risk Assessment; Written Control Scheme; Implementation of Control Scheme; and Record Keeping. While there was compliance at the majority of sites, breaches of the legislation were found at 625 sites (33% of those inspected), leading to 409 Improvement Notices (compelling dutyholders to make improvements to health and safety breaches of law in a given timeframe) and 12 Prohibition Notices (compelling dutyholders to stop work until they have remedied breaches in health and safety law) being served at 229 sites (12.0% of those inspected). Data from the intervention programme was analysed to identify root causes of these breaches of legislation on Legionella control. The majority of Improvement Notices (53%) were issued for the 'lack of effective implementation of a Written Control Scheme', with 'Risk Assessment' and 'Written Control Scheme' both accounting for 23%. More detailed examination showed major problems to be lack of training; failure to maintain the cleanliness of cooling towers and the water within them; risk assessments either being absent or not up to date, i.e., no longer representing the risks present; and Written Control Schemes being absent or insufficiently detailed. This provides a valuable data resource for dutyholders, so that they can understand where they need to focus to achieve significant improvement in legal compliance and therefore reduce the risk of LD for employees and members of the public affected by their workplace, and valuable data for regulators to target future interventions aimed at improving dutyholder compliance leading to better protection of workers and members of the public.

Performance Testing of a Venturi-Based Backpack Spray Decontamination System.

Introduction: The performance of 2 disinfectant chemicals, peracetic acid (PAA) and hypochlorous acid (HOCl), was evaluated using a Venturi-nozzle-based light decontamination system (LDS) for delivery. The atomization equipment combined low-pressure air and disinfectant via a handheld lance, producing a fine, dense aerosol. A range of microorganisms, including Bacillus cereus and Bacillus anthracis (Vollum) spores, were used as test challenges to evaluate chemicals and equipment. Methods: The tests undertaken included assessments over fixed and variable exposure times, use of multiple surface materials, and a live agent challenge. Results: Over a fixed-time exposure of 60 minutes, aerosolized PAA gave 7- to 8-log reductions of all test challenges, but HOCl was less effective. Material tests showed extensive kill on most surfaces using PAA (≥6-log kill), but HOCl showed more variation (4- to 6-log). Testing using B. anthracis showed measurable PAA induced spore kill inside 5 minutes and >6-log kill at 5 minutes or over. HOCl was less effective. Discussion: The results demonstrate the importance of testing decontamination systems against a range of relevant microbiological challenges. Disinfectant efficacy may vary depending on product choice, types of challenge microorganisms, and their position in a treated area. The most effective disinfectants demonstrate biocidal efficacy despite these factors. Conclusion: The data confirmed PAA as an effective disinfectant capable of rapidly killing a range of microorganisms, including spores. HOCl was less effective. The LDS system successfully delivered PAA and HOCl over a wide area and could be suitable for a range of frontline biosecurity applications.

A unified personal protective equipment ensemble for clinical response to possible high consequence infectious diseases: A consensus document on behalf of the HCID programme.

The importance of appropriate personal protective equipment (PPE) as a component of healthcare worker (HCW) protection was highlighted during the Ebola virus disease (EVD) outbreak in West Africa. The large number of HCW deaths in Africa was in part due to lack of resources or prior training in PPE usage. As part of the Ebola legacy, the High Consequence Infectious Disease (HCID) programme was initiated by NHS England and Public Health England (PHE) to improve preparedness for Ebola and other infections that not only endanger the life of the patient, but also pose particular dangers to HCWs. A systematic review identified national standardisation of PPE protocols as a priority, but recognised that a lack of safety data limited the ability to mandate any one protocol. A simulation-based exercise was developed to assess the safety of PPE ensembles in use in the UK during first assessment of a patient with a possible HCID. A mannequin was adapted to expose volunteer HCWs to synthetic bodily fluids (vomit, sweat, diarrhoea and cough), each with a different coloured fluorescent tracer, invisible other than under ultraviolet (UV) light. After exposure, HCWs were examined under UV lights to locate fluorescent contamination, and were screened again after removing PPE (doffing) to detect any personal contamination. The exercise was videoed, allowing retrospective analysis of contamination events and user errors. The simulation testing identified significant HCW contamination events after doffing, related to protocol failure or complications in PPE doffing, providing conclusive evidence that improvements could be made. At a workshop with an expert stakeholder group, the data were examined and a unified PPE ensemble agreed. This ensemble was then tested in the same simulation exercise and no evidence of any HCW contamination was seen after doffing. Following further review by the working group, a consensus agreement has been reached and a unified 'HCID assessment PPE' ensemble, with accompanying donning and doffing protocols, is presented here.

Gypsum in animal slurry systems enhances generation of hydrogen sulphide and increases occupational exposure hazard.

Hydrogen sulphide gas (H2S) produced by sulphate reducing bacteria (SRB) in stored animal slurry is highly toxic and, if emitted into poorly ventilated confined spaces, can build up to concentrations capable of causing asphyxiation. Therefore it is important to understand factors influencing H2S emission from slurry. Powdered gypsum (hydrated calcium sulphate) may be used as animal bedding and, if it enters slurry systems, could be metabolised by SRB and further increase H2S generation. Cattle slurry and cattle bedding collected from farms was used in laboratory-scale experiments sealed in 20litre vessels fitted with mechanical stirrers. H2S was monitored in head space above the slurry using real-time gas detectors before and after stirring, and before and after adding 1% of two sources of gypsum powder. In one set of experiments, gypsum was already present in the slurry having been used in bedding on the farm. H2S monitoring continued daily for up to 25days. Before stirring, H2S levels in head spaces were minimal. After stirring, even without gypsum, maximum head space H2S levels with slurry or bedding ranged from 330 to 1190ppm. By comparison, the UK short-term (15min) Workplace Exposure Limit is 10ppm. Statistically significant increases in H2S levels were associated with gypsum addition, as high as 1772ppm with slurry and 3940ppm with bedding. Emissions peaked at around day 15 with slurry and bedding to which gypsum was freshly added, but within 5days when added to slurry already containing farm-added gypsum. Levels of H2S produced from stirred slurry would constitute a hazard to anyone exposed to it, and adding gypsum further increased emission levels. Therefore, if gypsum residues enter slurry it could increase the risk of H2S accumulation in confined spaces associated with slurry systems. It is important therefore to take this into account in managing risk.

Systematic review of respiratory outbreaks associated with exposure to water-based metalworking fluids.

INTRODUCTION: Potential demographic risk factors for outbreaks of respiratory disease due to water-based metalworking fluids (MWFs) were investigated through systematic review of published outbreak investigations. METHODS: Search terms were selected by a multidisciplinary team, assisted by an experienced library information service. Several computerized literature databases were searched for articles published between January 1990 and October 2011, relating to ill health outbreaks due to MWFs. Papers meeting the search criteria were reviewed in detail, and their references checked for additional articles. Study design and demographic details of the outbreak were extracted from the selected articles and entered into standardized evidence tables. RESULTS: Thirty-five articles relating to investigations of 27 outbreaks of respiratory ill health attributed to MWF exposure were identified. The majority of reports were case series of disease or observational cross-sectional studies of symptoms and hygiene measurements. Eight of the outbreak investigations included an element of case-control analysis. Most outbreaks were from the USA, had occurred in large car- or aeronautical-manufacturing plants, and were associated with the use of central shared sumps. Hygiene studies have not demonstrated consistent risk factors for respiratory outbreaks, in terms of the type of MWF utilized, degree of microbial contamination, or levels of personal exposure. Six studies were identified that found workers with MWF exposure during outbreaks were more likely to report respiratory or systemic symptoms than unexposed control workers. Six case-control analyses were also identified that found workers with extrinsic allergic alveolitis (EAA) were more likely to demonstrate certain immune responses to microbial contaminants and/or used MWFs than workers without EAA. CONCLUSION: Despite a number of detailed workplace and immunological studies of asthma and alveolitis outbreaks in MWF-exposed workforces, our understanding of their aetiology remains limited.

Genome-wide atlas of gene expression in the adult mouse brain.

Molecular approaches to understanding the functional circuitry of the nervous system promise new insights into the relationship between genes, brain and behaviour. The cellular diversity of the brain necessitates a cellular resolution approach towards understanding the functional genomics of the nervous system. We describe here an anatomically comprehensive digital atlas containing the expression patterns of approximately 20,000 genes in the adult mouse brain. Data were generated using automated high-throughput procedures for in situ hybridization and data acquisition, and are publicly accessible online. Newly developed image-based informatics tools allow global genome-scale structural analysis and cross-correlation, as well as identification of regionally enriched genes. Unbiased fine-resolution analysis has identified highly specific cellular markers as well as extensive evidence of cellular heterogeneity not evident in classical neuroanatomical atlases. This highly standardized atlas provides an open, primary data resource for a wide variety of further studies concerning brain organization and function.

An outbreak of extrinsic alveolitis at a car engine plant.

BACKGROUND: Twelve workers from a car engine-manufacturing plant presented with extrinsic allergic alveolitis (EAA), with heterogeneous clinical, radiological and pathological findings. They were exposed to metalworking fluids (MWF) that cooled, lubricated and cleaned the machines. METHODS: They were characterized by history, examination, lung function testing, radiology, bronchoscopic lavage, lung biopsy and serology. Sera were tested for precipitins to a crude extract of used MWF and to reference cultures of bacteria suspected to be implicated. RESULTS: All were males and none were current smokers. All had dyspnoea, many had weight loss and cough, but only half had influenza-like symptoms. Only half had auscultatory crackles. Five had peak flow variability, four with an occupational component. There was overall restrictive spirometry, decreased lung volumes and reduced gas transfers. Ten had radiological evidence of interstitial lung disease. Seven (of eight) had lymphocytosis on bronchial lavage, including the two with inconclusive radiology. Seven (of 11) had lung biopsies showing inflammatory infiltrates, two with fibrosis and one with granulomas. Three (of 11) had strong positive precipitins to an extract of the used MWF from the plant. Molecular biological analysis of the MWF revealed Acinetobacter and Ochrobactrum. Precipitins to Acinetobacter were detected in seven of 11 workers tested (and four of 11 control workers). Precipitins to Ochrobactrum were detected in three of 11 workers tested (and three of 11 control workers). CONCLUSION: This is the largest series reported in Europe of EAA due to an aerosol of microbiologically contaminated MWF in heavy manufacturing industry.

Respiratory symptoms, immunology and organism identification in contaminated metalworking fluid workers. What you see is not what you get.

BACKGROUND: Metal working fluids (MWF) constitute a significant respiratory hazard, although symptoms experienced by workers are often poorly investigated and attributed. AIMS: A single possible case of extrinsic allergic alveolitis (EAA) led to a formal workplace investigation. It was clear that other exposed workers were affected. The aim of this study was to accurately quantify the clinical, immunological and microbiological findings in MWF workers following presentation of a sentinel case. METHODS: Eleven of 21 individuals participated; eight were assessed by symptom questionnaire, spirometry and serology and three workers provided blood samples only. The microbes cultured from MWF and air samples were used to determine the presence of precipitating antibodies. RESULTS: Work-related respiratory symptoms were reported in six of eight individuals questioned, two of these complaining of 'flu-like' symptoms. Personal breathing zone measures identified 2.1 x 10(3) to 1.1 x 10(5) colony-forming units/m3 air (CFU/m3). Pseudomonas fluorescens was isolated from air samples. Despite visible 'fungal' contamination of MWF, airborne fungi were detectable in only one sample, at 486 CFU/m3 air. MWF cultured Eurotium sp., Fusarium sp. and Pseudomonas sp. Precipitating IgG antibodies to Pseudomonas sp. were identified in 4/11 and to an extract of the MWF in 3/11. IgG to Pseudomonas was elevated in the two individuals who had the strongest precipitating bands to Pseudomonas sp. CONCLUSIONS: Workplaces with possible EAA must be investigated promptly, thus allowing clinical assessment to be contemporary to exposures and accurate microbiological profiling included to identify the likely cause.